Cisco C891F-K9 reset factory defaults
Connect a serial cable with baud 9600 to your cisco device and power on the device. Now select Special Command > Break in PuTTY to interrupt the boot command:
System Bootstrap, Version 15.4(1r)T1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2014 by cisco Systems, Inc.

Total memory size = 512 MB
Field Upgradeable ROMMON Integrity test
_______________________________________
ROM: Digitally Signed Production Software
C891F-K9 platform with 524288 Kbytes of main memory
Main memory is configured to 32 bit mode

Upgrade R
WARNING: Break key entered while upgrade ROMMON was initializing.
Do you want to fall back to readonly ROMMON? (y/n) [n] -
Upgrade ROMMON initialized


monitor: command "boot" aborted due to user interrupt
rommon 1 >




type confreg or confreg 0x2142
confreg
rommon 2 > confreg


Configuration Summary
(Virtual Configuration Register: 0x2102)
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C891F-K9

do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]:
enable "use net in IP bcast address"? y/n [n]:
disable "load rom after netboot fails"? y/n [n]:
enable "use all zero broadcast"? y/n [n]:
enable "break/abort has effect"? y/n [n]:
enable "ignore system config info"? y/n [n]: y
change console baud rate? y/n [n]:
change the boot characteristics? y/n [n]:


Configuration Summary
(Virtual Configuration Register: 0x2142)
enabled are:
load rom after netboot fails
ignore system config info
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C891F-K9

do you wish to change the configuration? y/n [n]:


You must reset or power cycle for new config to take effect



Now type reset to restart the device:
reset
rommon 3 > reset



System Bootstrap, Version 15.4(1r)T1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2014 by cisco Systems, Inc.

Total memory size = 512 MB
Field Upgradeable ROMMON Integrity test
_______________________________________
ROM: Digitally Signed Production Software
C891F-K9 platform with 524288 Kbytes of main memory
Main memory is configured to 32 bit mode

Upgrade ROMMON initialized


IOS Image Load Test
___________________
Digitally Signed Production Software
Self decompressing the image : ##########[...]########## [OK]
*** No sreloc section
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x022ECEC0
-----------------------------------------------
TOTAL: 0x022ECEC0

Rounded IOMEM up to: 34Mb.
Using 6 percent iomem. [34Mb/512Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.3(3)M6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 04-Aug-15 05:50 by prod_rel_team


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Installed image archive
Cisco C891F-K9 (revision 1.0) with 488524K/35763K bytes of memory.
Processor board ID FCZ231990YB
1 FastEthernet interface
9 Gigabit Ethernet interfaces
1 Serial interface
1 ISDN Basic Rate interface
1 terminal line
1 Virtual Private Network (VPN) Module
DRAM configuration is 32 bits wide
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash (Read/Write)


--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no


Press RETURN to get started!


*Jan 2 00:00:00.971: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name c800 Next reboot level advipservices and License advipservices


Um diesen Eintrag vollständig sehen zu können, müssen Sie ein Kunde der Securebit AG sein. Dazu können Sie ein belibites Produkt aus unserem Sortiment bestellen.

Sollten Sie bereits Kunde sein, können Sie sich hier anmelden.